Big end roller (£2.00) Big end roller 7/32 x 7/16 standard also plus 0.001 and 0.002 see common parts Qty

Big end roller early (£1.75) Big end roller early 3/16 x 7/8 Qty

Brake Pedal spring (£5.85) Model H,SD brake peadle spring spring. Qty

carb mainjet filter bolt brass (£6.50) carb mainjet filter bolt brass fit most twin barrel carbs. Qty

Carbuorret top fuel nut (£3.90) 1 off Carburettor top fuel nut. Special thread to hold olive tight on to taper 9/16 x 25tpi Qty

Carburattor air filter (£25.50) Made from steel ready to plate. Qty

Carburettor filter locking ring (£12.50) Carburettor filter locking ring Style air filter Qty

Carburettor fuel bowl olive (£3.90) Carburettor fuel bowl olive. Brass for 3/16 fuel line. Qty

Carburettor nut cap (£20.00) Carburettor nut cap Ready to be plated Fits H,sd,Riardo and P etc Qty

Carburettor throttle spring set (£6.50) Carburettor throttle spring set ,2 springs 3/4 dia X 3 3/8 Qty

Carrier stud Model H (£4.85) Carrier stud Model H.3/8 one end and 5/16 the other x 600thou hex Qty

Clutch spring set cs box (£18.00) Model H clutch spring set cs box. Set of 6 springs 0.600 Dia X 1.2 Inch Long Qty

Cotter Pin (£2.50) Cotter Pin for Cs Kick start Qty

Crank case nuts 1/4 x 24 (£2.95) Crank case nuts 1/4 x 24 .Also fits Primary cover Qty

Crankcase bolt 1/4 x24 Tpi (£3.50) Crankcase bolt domed head 1/4-24tpi 3 5/8 long 4 needed. Qty

Cs clutch nut (£4.50) Cs clutch nut 5/8 thread Qty

Cs clutch plates (£14.00) Your clutch plates religned - need yours to exchange otherwise £40.00 per new plate Qty

Cs gear box kick start spring (£8.50) Cs gear box kick start spring up to around 1918 Qty

Cs Gear change casting (£25.00) Cs Gear change casting come as bar casting only Qty

CS gearbox nuts for front cover (£1.50) CS gearbox nuts 1/4 dia 26tpi Qty

Cs kick start rubber (£4.25) Cs kick start rubber .5/8 bore 3 1/2 long. Qty

Cs kickstart clip (£9.50) Cs kickstart clip Qty

Cs Kickstart spring late (£8.50) Cs Kickstart spring late from aroun 1919 has end of wire bent over to go into drilled holes around kick starter boss Qty

Cs pulley nut large (£6.50) Cs pulley nut 1.050 thread Left hand Qty

Cylinder base nuts (£3.50) Cylinder base nuts 5/16 BSW 18 TPI. Qty

D type Foot rubbers one pair (£27.00) D type Foot rubbers one pair with triumph cast into them Qty

Decompressor spring Large part no 95 (£3.25) Decompressor spring. Large 0.590 dia x 1.200 long Qty

Decompressor spring small part no 99 (£3.00) Decompressor spring, small 0.290 dia x 0.420 long. Qty

Engine valve (£32.00) Engine valve 9 mm stem overall length 5.310" large slot 0.100" wide. Inlet or exhaust. Qty

Exhaust lifter bolt special (£15.00) Exhaust lifter bolt special for cable to go throught Qty

Exhaust pipe (£265.00) Exhaust pipe Fits Model H. Made in small batches as per the original ones comes apart in the middle to adjust for each bike with a lap joint in body. down pipe Nickled with exhaust nut fitted (picture to be updated) Qty

Exhaust valve lifter spring (£3.00) Exhaust valve lifter spring 0.300 od x 1 3/8 long. Qty

Filler cap 1 5/8 OD (£40.00) Filler cap 1 5/8 OD for1913, 1914, H and SD with leather washer ready to be nickel. we can now stamp them with the original rotherhams stamp for a extra £10.00 please enquire Qty

Filler neck 1 5/8 od (£20.00) Fits models 1913, 1914, H, SD for 1 5/8 cap. Qty

Fork Nuts 7/16 (£3.50) Fork Nuts 7/16 fit front forks on late veterans and Model H. price each Qty

Fork spring (£120.00) Fork spring of oval wire section with both nut and draw bolt fitted. Heat treated and ready to plate.The expensive part was getting someone to roll the oval wire section. 4 1/4 long. Qty

Front brakes complete Front brakes complete with tube clamps and handle bar cannon.Only made to order now enquire to ian@veterantriumph.co.uk Qty

Front mudguard Lobster tail (£170.00) Fits 1914 , Model H and SD front. Lobster tail and front section of guard as photo. Qty

Fuel cap spring (£3.00) Fuel cap spring 0.400 dia x 0.880 long Qty

Gearbox adjuster bolt and nut (£6.50) Gearbox adjuster bolt and nut special thread 9/32 Qty

H exhaust nut. (£22.00) H exhaust nut. Fits Model H ,Sd and ricardos Qty

Halk link for primary chain (£3.50) Halk link for primary chain suits our chain. Qty

Handle bars for Model H (£40.00) Handle bars for Model H Qty

Hints and tips for model H , SD ,R (£6.50) Reprint of hints and tips for model H , SD ,R Qty

Lower yoke bearing (£42.00) Lower yoke bearing set complete with 1/8 balls. Case hardened and ready to nickle Qty

Lubricator lagre (£7.50) Lubricator lagre with ball and engraved with triumph Qty

Lubricator screw (£2.00) Lubricator screw 1/8 dia x 1/4 long Qty

Mag spring (£2.00) Mag spring used in Bosch advanced unit Qty

Mag stay nut (£2.00) Mag stay nut 1/4 x 24tpi thread x 1/4 wide x 440thou hex Qty

Mag stay set screw (£3.00) Mag stay set screw Qty

Mag strap (£13.00) Mag strap that goes from frame to mag platform. Qty

Magneto timing cover (£65.00) Magneto timing cover and inter casting need machining to suit your bike Qty

Mc 22 main bearings (£45.00) Mc 22 main bearings 22id 50 od 17 wide. Now obsolete, we have them made in batches of 50 to keep price down.single row deep grove bearing. Also used in Nortons and Sunbeams. Qty

Mc22 special (£50.00) We have had a small batch of mc22 special made same OD and width as original but id is 21.80mm. So if you have a crank with damaged on the journals or they are bent you can get them reground true. Qty

Model H piston (£130.00) Model H piston aluminium plus 20 thou with rings and pin. other sizes to plus 60 please enquire Qty

Model H Primary Aluminium cover (£100.00) Model H Primary Aluminium cover later type for shock Drive with bump in the middle Qty

Mudguard stay bolts 1/2 (£3.50) Mudguard stay bolts 1/4 x 24 Tpi x 1/2 long used on mudgaurds and other places. Qty

Mudguard stay bolts 3/8 (£3.50) Mudguard stay bolts 1/4 x 24 Tpi x 3/8 long used on mudgaurds and other places. Qty

Oil primer cap (£9.00) Oil primer cap, needs nickling. We can make complete tanks as well from £600.00 with all the fittings. Please enquire. Qty

Primary cover badge Badge to fit primary cover of model H, pre shock absorber, cover brass etched. Qty

Rear brake rod pivot (£20.00) Rear brake rod pivot Qty

Rear Brake Spring (£9.85) Brake spring fits H,SD,R,P stops shoe rubbing Qty

Rear brake steel plate. (£6.00) Rear brake steel plate. Qty

Rear wheel nut (£4.50) rear wheel nut model H 1/2x 20 tpi Qty

Rubber Grips 4 1/2 long (£27.00) Rubber Grips 4 1/2 long for 7/8 bars fits H and later models.John Bull Type open both ends 1 Pair per set. Qty

Seat bolt (£5.00) seat bolt 5/16-18tpi x 4 3/8 long domed head. Qty

Seat bolt nut 5/16 18 tpi (£3.00) seat bolt nut 5/16 18 tpi Qty

Spares manual H 1920. (£6.50) Spares manual H 1920. Some early parts, not much Qty

Spares manual, Model H,SD,R 1925 (£6.50) Spares manual, Model H,SD,R 1925 copy from our original. Qty

Sprocket 17 tooth (£70.00) New sprocket 17 tooth Qty

Stem clamp bolt (£6.00) Stem clamp bolt 5/16 whit x 1 3/4 with nut Qty

Stem clamp nut 5/16 whit (£2.00) Stem clamp nut 5/16 whit x 18tpi x 440 hex also used on rear carrier as the clamp nuts. Qty

Tank ferrals (£5.00) Fits bottom of tanks for the taps to screw into must be lockup then soldered into tank. Qty

Tank main fuel tap (£40.00) Tank main fuel tap, complete, needs nickling. We can make complete tanks as well from £600.00 with all the fittings. Please enquire. Qty

Tank oil pump H (£45.00) Tank oil pump for model H also Fits late veterans and Sd and some model P Qty

Tank primer tap (£60.00) Tank primer tap, complete, needs nickling. We can make complete tanks as well from £600.00 with all the fittings. Please enquire. Qty

Timing chain (£6.50) £6.50 per foot. Good quality chain Qty

Timing chain link. (£2.50) Timing chain link. Qty

Timing cover screw (£2.50) Timing cover screw 5 mm dia x 26 tpi 1 1/16 long. Qty

Timing cover Triumph name plate (£12.00) Timing cover Triumph name plate, brass Qty

Top bearings set complete (£40.00) Top bearings set complete with 1/8 balls, case hardened and ready to be nickled. Qty

Top yoke bearing housing (£39.00) Top yoke bearing housing for spring to clamp on and retain bearing in. Qty

Twin lever (£120.00) Twin lever all newly made from steel no brass to bend like repro ones getting made. Made to suit 7/8 bar. Ready to nickel comes with clamp plate and 2 screws Qty

Twin lever Nickled (£160.00) Twin lever all newly made from steel no brass to bend like repro ones getting made. Made to suit 7/8 bar.Nickeled comes with clamp plate and 2 screws. Qty

Valve cap copper washer (£2.25) Valve cap copper washer, 1.775 id x 0.073 thick. Qty

Valve cap plain (£35.00) Valve cap to fit Model H and SD cylinders, made from brass ready to plate. Qty

Valve cap plug (£37.00) Valve cap to fit Model H and SD cylinders, made from brass, ready to plate M18 spark plug thread. Qty

Valve guide Model H (£20.00) Valve guide Model H reamed to size 9.02 Qty

Valve keeper (£8.50) Valve keeper to fit 9 mm stems Models H and SD casehardened Qty

Valve protector wood (£15.00) Valve protector wood, fits Model H and SD Qty

Valve spring H (£14.00) Valve spring set for Model H, 33.5 dia x 71 long, set of 2 Qty

Vavle lifter arm (£16.00) Vavle lifter arm for later model H after 1916 approx Qty